Stock SPARK 60 Average Speed 43 @ 7150 RPM
R&D SPARK Stage 3 Kit 57-58 @ 8650 RPM

 

Description of Parts RPM Top Speed
R&D SPARK R3 Reprogrammed ECU
Part #: 803-01902
8650 57-58 mph
R&D SPARK Aquavein Intake Grate
Part #: 113-96001
   
R&D SPARK Pump Seal Kit
Part #: 163-81901
   
R&D SPARK Power Filter Kit
Part # 203-00900
   
R&D SPARK Sponson Kit
Part #: 123-96002
   
R&D SPARK Stainless Steel Pump Liner kit
Part # 133-50900
   
R&D SPARK Ride Plate
Part # 123-80910
   
Total: $2031.38    

Parts/Kit Overview

The R&D Spark 60/90 Stage 3 Kit was developed to significantly improve overall handling, pump efficiency, and engine performance with easy to install entry level performance parts. The R&D Stage 3 Kit adds Monster Low End Performance Punch and aggressive Mid Range Pull! Each component part listed can be installed and used as a stand-alone product. The R&D Kit has been extensively tested in all water conditions proving its performance and reliability. The addition of the R&D Stage 3 Kit will add a full 15 miles per hour to top speed performance and transform the Spark into a great handling and fun watercraft with one of the best mile per gallon values on the water. Ride nearly all day on 7 gallons of fuel! Call and order up some fun today.

  • The R&D Spark R3 ECU Reprogramming Service will improve overall engine performance by boosting acceleration, improving mid range pulling power, and top end performance gains of up to 15 miles per hour. R&D has improved the overall ignition timing table with timing advance additions, as well as improved the fuel table in areas that could be improved. The O.E.M. “low ceiling” rev limiter has been raised to 8850 to allow the engine to rev without tagging the rev limiter which will allow the Spark to accelerate and stay hooked up in rough chop. The Popular R&D R3 ECU Reprogramming is one of the best performance upgrades that can be added to Spark.

  • The R&D Spark Aquavein Intake Grate will noticeably increase overall handling performance, significantly reduce cavitation, increase acceleration, and add 1+ mph to top end performance in flat water conditions! A 2-3 mph speed improvement (over stock) will be gained in rough water conditions. The Spark Aquavein will deliver a noticeable increase in rear end traction, and top speed stability. Low and high speed cornering stability is also significantly increased. The R&D Aquavein is a must have performance part addition.

  • The R&D Spark Pump Seal Kit will seal up the pump inlet to noticeably reduce cavitation. Positive Pump hook-up, and top speed performance are increased with a perfectly sealed pump system.

  • The R&D Spark Power Filter Kit will add a noticeable increase in throttle response and overall power by opening up and allowing more air flow over the super restrictive O.E.M. air plenum box. The O.E.M. filters are known to be over restrictive causing sluggish low-end power. The R&D Filter Kit incorporates and adds needed intake track length proven to increase overall torque and power on 4 stroke engines. The R&D Filter is easy to install in 30 minutes, adds peak rpm’s and power with a great sound tone. The R&D Air Filter element is lifetime serviceable over the restrictive non serviceable stock filter.

  • The R&D Spark Pro Series Sponson Kit offers 2 rider preferred adjustable blade positions that will accommodate settings for the recreational rider or closed course racer. The R&D precision cast aluminum backing plate and Race Inspired sponson blade will significantly improve low and high speed cornering capabilities, and add unmatched straight line stability. The R&D Pro Series Sponson Kit will reduce high speed chine walking.

  • The OEM plastic pump liner wears out quickly and is upgraded with the R&D Stainless Steel Pump Liner/Wear ring to provide proper prop-to-wear-ring tolerance.

  • The R&D Spark Pro Series Hull Extension Trim Tab Kit will be a necessary add on to the Spark 60 specifically. The R&D Trim Tab Kit will extend the length of the hull to substantially reduce cavitation and bow jump that will be noticed with the R&D R3 ECU. The added engine power from the R&D ECU will make the spark jump like a dolphin! The R&D Hull Trim Tabs will keep the hull planted, hooked up and driving forward. The tabs have Zero Speed loss, and a big overall handling improvement.

NOTE: For Performer Kit applications in extreme rough water or ocean use where the O.E.M. impellor is desired to be used, R&D recommends the installation of an R&D Pump Cone Kit Pt. # 163-95900. R&D also offers Pro Pitch Impellor Services to the stock impellor to achieve your desired running rpm range. Call R&D for custom impellor tune combinations available for the spark.

  © 2004 R&D Performance Products USA. All Rights Reserved.